Using the Photo-Piezoelectric Effect of AuPt@BaTiO3 Oxidase Mimetics for Colorimetric Detection of GSH in Serum.

Nanozymes possess major advantages in catalysis and biosensing compared with natural nanozymes. In this study, the AuPt@BaTiO3 bimetallic alloy Schottky junction is prepared to act as oxidase mimetics, and its photo-piezoelectric effect is investigated. The synergy between the photo-piezoelectric effect and the local surface plasmon resonance enhances the directional migration and separation of photogenerated electrons, as well as hot electrons induced by the AuPt bimetallic alloy. This synergy significantly improves the oxidase-like activity. A GSH colorimetric detection platform is developed based on this fading principle. Leveraging the photo-piezoelectric effect allows for highly sensitive detection with a low detection limit (0.225 µM) and reduces the detection time from 10 min to 3 min. The high recovery rate (ranging from 99.91% to 101.8%) in actual serum detection suggests promising potential for practical applications. The development of bimetallic alloy heterojunctions presents new opportunities for creating efficient nanozymes.

Exceptional Magnetocaloric Responses in a Gadolinium Silicate with Strongly Correlated Spin Disorder for Sub-Kelvin Magnetic Cooling.

The development of magnetocaloric materials with a significantly enhanced volumetric cooling capability is highly desirable for the application of adiabatic demagnetization refrigerators in confined spatial environments. Here, the thermodynamic characteristics of a magnetically frustrated spin-7/2 Gd9.33[SiO4]6O2 is presented, which exhibits strongly correlated spin disorder below ≈1.5 K. A quantitative model is proposed to describe the magnetization results by incorporating nearest-neighbor Heisenberg antiferromagnetic and dipolar interactions. Remarkably, the recorded magnetocaloric responses are unprecedentedly large and applicable below 1.0 K. It is proposed that the S = 7/2 spin liquids serve as versatile platforms for investigating high-performance magnetocaloric materials in the sub-kelvin regime, particularly those exhibiting a superior cooling power per unit volume.

Highly efficient MoS2/MXene aerogel for interfacial solar steam generation and wastewater treatment.

Interfacial solar steam generation using aerogels holds great promise for seawater desalination and wastewater treatment. However, to achieve aerogels with both durable, high-efficiency evaporation performance and excellent salt resistance remains challenging. Here, a molybdenum disulphide (MoS2) and MXene composite aerogel with vertical pore channels is reported, which has outstanding advantages in mechanical properties, water transportation, photothermal conversion, and recycling stability. Benefiting from the plasmon resonance effect of MXene and the excellent photothermal conversion performance of MoS2, the aerogel exhibits excellent light absorption (96.58 %). The aerogel is resistant to deformation and able to rebound after water absorption, because of the support of an ordered vertical structure. Moreover, combined with the low water evaporation enthalpy, low thermal conductivity, and super hydrophilicity, the aerogel achieves an efficient and stable evaporation rate of about 2.75 kg m-2h-1 under one sun and exhibits excellent self-cleaning ability. Notably, the evaporator achieves removal rates of 99.9 % for heavy metal ions and 100 % for organic dyes, which has great potential in applications including seawater desalination and wastewater purification.

Using Multistage Energy Barrier of Heterojunctions in Improving Cr(VI) Detection.

Detecting heavy metals in seawater is challenging due to the high salinity and complex composition, which cause strong interference. To address this issue, we propose using a multistage energy barrier as an electrochemical driver to generate electrochemical responses that can resist interference. The Ni-based heterojunction foams with different types of barriers were fabricated to detect Cr(VI), and the effects of the energy barriers on the electrochemical response were studied. The single-stage barrier can effectively drive the electrochemical response, and the multistage barrier is even more powerful in improving sensing performance. A prototype Ni/NiO/CeO2/Au/PANI foam with multistage barriers achieved a high sensitivity and recovery rate (93.63-104.79%) in detecting seawater while resisting interference. The use of multistage barriers as a driver to resist electrochemical interference is a promising approach.

Triboelectric Nanogenerator for Droplet Energy Harvesting Based on Hydrophobic Composites.

Triboelectric nanogenerators (TENG) have shown great potential in harvesting energy from water. For the TENG that harvests water energy, surface hydrophobicity is crucial for its performance. In this paper, we prepare a hydrophobic composite film of Polyvinylidene Fluoride/Polydimethylsiloxane/Polytetrafluoroethylene (PVDF/PDMS/PTFE) and an electrode of Polyaniline/Carbon nanotubes/Silver nanowires (PANI/CNTs/AgNWs) by electrospinning technology and a doping method, respectively, which are served as the friction layer and top electrode of TENG. The contact angle of the hydrophobic film and electrode both reach over 120°, which makes the separation process between water and the interface complete and promotes the output of TENG. The open-circuit voltage (Voc) and short-circuit current (Isc) can reach 150 V and 60 µA approximately. In addition, the composite electrode can be applied in the preparation of complex electrode shapes. Furthermore, the different reactions of TENG to different liquids indicate that it may contribute to liquid-type sensing systems. This work presents an efficient approach to fabricating hydrophobic films and electrodes, laying a foundation for the development of TENG for harvesting water energy.

High-output soft-contact fiber-structure triboelectric nanogenerator and its sterilization application.

Infectious diseases are spreading rapidly with the flow of the world's population, and the prevention of epidemic diseases is particularly important for public and personal health. Therefore, there is an urgent need to develop a simple, efficient and non-toxic method to control the spread of bacteria and viruses. The newly developed triboelectric nanogenerator (TENG) can generate a high voltage, which inhibits bacterial reproduction. However, the output performance is the main factor limiting real-world applications of TENGs. Herein, we report a soft-contact fiber-structure TENG to avoid insufficient friction states and to improve the output, especially at a high rotation speed. Rabbit hair, carbon nanotubes, polyvinylidene difluoride film and paper all contain fiber structures that are used to guarantee soft contact between the friction layers and improve the contact state and abrasion problem. Compared with a direct-contact triboelectric nanogenerator, the outputs of this soft-contact fiber-structure TENG are improved by about 350%. Meanwhile, the open-circuit voltage can be enhanced to 3440 V, which solves the matching problems when driving high-voltage devices. A TENG-driven ultraviolet sterilization system is then developed. The bactericidal rate of this sterilization system can reach 91%, which significantly reduces the risk of disease spread. This work improves a forward-looking strategy to improve the output and service life of the TENG. It also expands the applications of self-powered TENG sterilization systems.

Achieving remarkable energy storage enhancement in polymer dielectrics via constructing an ultrathin Coulomb blockade layer of gold nanoparticles.

High-energy density polymer dielectrics play a crucial role in various pulsed energy storage and conversion systems. So far, many strategies have been demonstrated to be able to effectively improve the energy density of polymer dielectrics, but sophisticated fabrication processes are usually needed which result in high cost and poor repeatability. Herein, an easy-operated sputtering and hot-pressing process is developed to significantly enhance the energy density of polymer dielectrics. Surprisingly, for the poly(vinylidene fluoride-hexafluoropropylene) films sputtered with merely 0.0064 vol% gold nanoparticles, the energy density is remarkably improved by 84.3% because of the concurrent enhancements in breakdown strength (by 37.5%) and dielectric permittivity (by 25.5%), which is demonstrated to have originated from the unique Coulomb blockade and micro-capacitor effect of the gold nanoparticles. It is further confirmed that this design strategy is also applicable for commercial biaxially oriented polypropylene and poly(methyl methacrylate). This work offers a novel, easy-operated and universally applicable route to improve the energy density of polymeric dielectrics, which paves the way for their application in modern electronics and power modules.

Strong Magnetocaloric Coupling in Oxyorthosilicate with Dense Gd3+ Spins.

Searching for working refrigerant materials is the key element in the design of magnetic cooling devices. Herein, we report on the thermodynamic and magnetocaloric parameters of an X1 phase oxyorthosilicate, Gd2SiO5, by field-dependent static magnetization and specific heat measurements. An overall correlation strength of |J|S2 ≈ 3.4 K is derived via the mean-field estimate, with antiferromagnetic correlations between the ferromagnetically coupled Gd-Gd layers. The magnetic entropy change -ΔSm is quite impressive, reaches 0.40 J K-1 cm-3 (58.5 J K-1 kg-1) at T = 2.7 K, with the largest adiabatic temperature change Tad = 23.2 K for a field change of 8.9 T. At T = 20 K, the lattice entropy SL is small enough compared to the magnetic entropy Sm, Sm/SL = 21.3, which warrants its potential in 2 -20 K cryocoolers with both the Stirling and Carnot cycles. Though with relatively large exchange interactions, the layered A-type spin arrangement ultimately enhances the magnetocaloric coupling, raising the possibilities of designing magnetic refrigerants with a high ratio of cooling capacity to volume.

Gold Sputtering at the Interfaces: An Easily Operated Strategy for Enhancing the Energy Storage Capability of Laminated Polymer Dielectrics.

Polymers with excellent dielectric properties are strongly desired for pulsed power film capacitors. However, the adverse coupling between the dielectric constant and breakdown strength greatly limits the energy storage capability of polymers. In this work, we report an easily operated method to solve this problem via sputtering the interface of bilayer polymer films with ultralow content of gold nanoparticles. Interestingly, the gold nanoparticles can effectively block the movement of charge carriers because of the Coulomb blocking effect, yielding significantly enhanced breakdown strength. Meanwhile, the gold nanoparticles can act as electrodes to form numerous equivalent microcapacitors, resulting in an obviously enhanced dielectric constant. Impressively, the polymer film with merely 0.01 vol % gold nanoparticles exhibits an obvious dielectric constant and breakdown strength, which are 129 and 131% that of the pristine polymer film, respectively. Consequently, a high energy density which is 176% of that of the pristine polymer film is achieved, and a high efficiency of 79.2% is maintained. Moreover, this process can be well combined with the production process of commercial dielectric polymer films, which is beneficial for mass production. This work offers an easily operated way to improve the dielectric capacitive energy storage properties of polymers, which could also be applicable to other materials, such as ceramics and composites.

Influence of Mechanical Screened Recycled Coarse Aggregates on Properties of Self-Compacting Concrete.

The use of recycled coarse aggregates (RA) in concrete is a sustainable alternative to non-renewable natural aggregate (NA) to fabricate concrete products using in concrete structures. However, the adhered mortar on the surface of RA would considerably impact the qualities of concrete products. As a practical treatment procedure, mechanical screening can remove the adhered mortar. This research aims to study the influence of mechanical screening on the fundamental properties of RA and the resulting self-compacting concrete (SCC). The RA were mechanically screened up to four times, and their physical properties including particle size distribution, water absorption, and crushing value were investigated. The properties of RA-SCC including workability, density, compressive and tensile strengths, modulus of elasticity, and microstructure were also examined. The results demonstrated that screening reduced the water absorption of RA from 6.26% to 5.33% and consequently enhanced the workability of RA-SCC. Furthermore, it was shown that increasing the screening up to twice improved the mechanical properties of concrete. In particular, screening increased the compressive strength of concrete by 15-35% compared to the concrete with unscreened RA. Similar improvements were found in tensile strength as well as the elastic modulus results. The microstructure of screened RA-SCC was comparable to that of the control concrete, showing minimal porosity and cracks along the interfacial transition zone. In conclusion, once or twice screening is recommended to the recycling facility plant to remove adequate amount of adhered mortar and fines while preventing damages to the RA. Improving the quality of RA via mechanical screening is one of the promising approaches to increase their potential for use in concrete, thereby reducing extraction of natural resources and promoting a circular economy.

Evaluation of Void Defects behind Tunnel Lining through GPR forward Simulation.

Voids, a common defect in tunnel construction, lead to the deterioration of the lining structure and reduce the safety of tunnels. In this study, ground-penetrating radar (GPR) was used in tunnel lining void detection. Based on the finite difference time domain (FDTD) method, a forward model was established to simulate the process of tunnel lining void detection. The area of the forward image and the actual void area was analyzed based on the binarization method. Both the plain concrete and reinforced concrete lining with various sizes of air-filled and water-filled voids were considered. The rationality of the model was verified by measured data. It was observed that the response mode of voids can be hyperbolic, bowl-shaped, and strip-shaped, and this depends on the void's width. Compared with the air-filled voids, water filling increases the response range of the voids and produces a virtual image. Although the diffracted wave caused by a steel bar will bring about significant interference to the void response, the center position of the voids can be accurately located using 3D GPR.

Construction motion data library: an integrated motion dataset for on-site activity recognition.

Identifying workers' activities is crucial for ensuring the safety and productivity of the human workforce on construction sites. Many studies implement vision-based or inertial-based sensors to construct 3D human skeletons for automated postures and activity recognition. Researchers have developed enormous and heterogeneous datasets for generic motion and artificially intelligent models based on these datasets. However, the construction-related motion dataset and labels should be specifically designed, as construction workers are often exposed to awkward postures and intensive physical tasks. This study developed a small construction-related activity dataset with an in-lab experiment and implemented the datasets to manually label a large-scale construction motion data library (CML) for activity recognition. The developed CML dataset contains 225 types of activities and 146,480 samples; among them, 60 types of activities and 61,275 samples are highly related to construction activities. To verify the dataset, five widely applied deep learning algorithms were adopted to examine the dataset, and the usability, quality, and sufficiency were reported. The average accuracy of models without tunning can reach 74.62% to 83.92%.

Three-Dimensional Artificial Transpiration Structure Based on 1T/2H-MoS2/Activated Carbon Fiber Cloth for Solar Steam Generation.

The rise of solar steam generation is an effective strategy to mitigate clean water shortages. However, achieving further improvements in conversion efficiency and stability remains a challenge. Here, 1T/2H-MoS2 nanosheets were uniformly assembled on activated carbon fiber cloth (A-CFC) through a facial hydrothermal method, and a three-dimensional (3D)-artificial transpiration device (ATD) was prepared using the plant transpiration process. The combination of activated carbon fiber cloth and 1T/2H phase MoS2 exhibits high light absorption (∼97.5%), excellent mechanical stability, large evaporation area, and easy escape of vapor. Additionally, the 3D hollow cone of the MoS2/carbon fiber cloth can effectively reduce radiative and convective energy loss and then achieve the enhancement of energy collection from the environment. An outstanding evaporation rate of 1.61 kg·m-2·h-1 with an optimum conversion efficiency of 97% under one sun is reached. Based on the facile fabrication, excellent stability, and high solar conversion efficiency, this nature-inspired design of 3D 1T/2H-MoS2/A-CFC is expected to facilitate large-scale applications for seawater purification and desalination.

Energy Conversion Analysis of Multilayered Triboelectric Nanogenerators for Synergistic Rain and Solar Energy Harvesting.

The triboelectric nanogenerator (TENG) is an emerging technology that offers excellent potential for the conversion of mechanical energy from rain into electricity for hybrid energy applications. However, a high-performance TENG is yet to be achieved because a quantitative analysis method for the energy conversion process is still lacking. Herein, a quantitative analysis method, termed the "kinetic energy calculation and current integration" (KECCI) method, which significantly improves the understanding of the mechanical-to-electrical energy conversion process, is presented. Based on the KECCI method, a high-performance TENG is developed by systematically optimizing a biomimetic surface structure and instant switch design, with 1.25 mA short-circuit current (Isc ), 150 V open-circuit voltage (Voc ), and a high energy-conversion efficiency of 24.89%. Furthermore, a multilayered TENG device is proposed for continuously harvesting the kinetic energy of raindrops for further improvement in the energy-conversion efficiency. Finally, the multilayered TENGs are integrated with organic photovoltaics, achieving all-weather energy harvesting. This work presents a validated theoretical basis that will guide further development of TENGs toward higher performances, which will promote the commercialization of hybrid TENG systems for all-weather applications.

Enhanced hydrogen storage properties of ZrTiVAl1-x Fe x high-entropy alloys by modifying the Fe content.

Lightweight ZrTiVAl high-entropy alloys have shown great potential as a hydrogen storage material due to their appreciable capacity, easy activation, and fast hydrogenation rates. In this study, transition metal Fe was used to improve the hydrogen storage properties of the equimolar ZrTiVAl alloy, and ZrTiVAl1-x Fe x (x = 0, 0.2, 0.4, 0.6, 0.8, 1) alloys were prepared to investigate the microstructure evolution and hydrogen storage properties. The results show that the ZrTiVAl1-x Fe x alloys are composed of a C14 Laves phase and Ti-rich HCP phase. With Fe substituting Al, the fraction of the C14 Laves phase increases and that of the HCP phase decreases. Besides, the interdendritic area fraction reaches the maximum when the Fe ratio is 0.2. The element V transferred to the C14 Laves phase from the HCP phase, which is caused by the strong affinity between V and Fe. The ZrTiVAl1-x Fe x alloys show enhanced hydrogenation kinetics and capacities. Notably, the ZrTiVFe alloy can reversely absorb 1.58 wt% hydrogen even at room temperature under 1 MPa H2. The reduced interdendritic phase is beneficial to shorten the H atom diffusion distance, thus improving the hydrogenation rates. Both the transfer of the hydrogen-absorbing element V to the C14 Laves phase and the increased fraction of the C14 Laves phase lead to the increase of hydrogen storage capacity with the addition of Fe. Moreover, the increased Fe content leads to an increase of average valence electron concentration (VEC), where a larger VEC destabilizes the hydrides, and the desorption temperature of ZrTiVAl1-x Fe x hydride decreases significantly.

Titanium carbide MXenes coupled with cadmium sulfide nanosheets as two-dimensional/two-dimensional heterostructures for photocatalytic hydrogen production.

Two-dimensional (2D)/2D heterostructures with close contact are believed to be important for photocatalysis owing to a 2D ultrathin structure, a large surface area, and an efficient carrier separation or transfer. In this study, we designed and prepared a unique 2D/2D cadmium sulfide (CdS) nanosheet (NS)@titanium carbide (Ti3C2) MXene composite photocatalyst. The results show that the CdS NSs can be controllably assembled on conductive Ti3C2 MXene via a one-step hydrothermal strategy. The 2D/2D CdS NS@Ti3C2 MXene composites with 5 mg of Ti3C2 MXene show a higher photocatalytic performance (1.73 mmol h-1 g-1) than pure CdS NSs (0.37 mmol h-1 g-1) and CdS NS@Ti3C2 MXene composites with other MXene contents (3 mg, 7 mg, 10 mg, and 20 mg). The improved photocatalytic activity can be attributed to the high surface area as confirmed by a BET analysis and enhanced charge separation activity between CdS and Ti3C2 MXene.

Phosphorous-doped 1T-MoS2 decorated nitrogen-doped g-C3N4 nanosheets for enhanced photocatalytic nitrogen fixation.

Herein, we report that the phosphorous-doped 1 T-MoS2 as co-catalyst decorated nitrogen-doped g-C3N4 nanosheets (P-1 T-MoS2@N-g-C3N4) are prepared by the hydrothermal and annealing process. The obtained P-1 T-MoS2@N-g-C3N4 composite presents an enhanced photocatalytic N2 reduction rate of 689.76 µmol L-1 g-1h-1 in deionized water without sacrificial agent under simulated sunlight irradiation, which is higher than that of pure g-C3N4 (265.62 µmol L-1 g-1h-1), 1 T-MoS2@g-C3N4 (415.57 µmol L-1 g-1h-1), 1 T-MoS2@N doped g-C3N4 (469.84 µmol L-1 g-1h-1), and P doped 1 T-MoS2@g-C3N4 (531.24 µmol L-1 g-1h-1). In addition, compared with pure g-C3N4 NSs (2.64 mmol L-1 g-1h-1), 1 T-MoS2@g-C3N4 (4.98 mmol L-1 g-1h-1), 1 T-MoS2@N doped g-C3N4 (6.21 mmol L-1 g-1h-1), and P doped 1 T-MoS2@g-C3N4 (9.78 mmol L-1 g-1h-1), P-1 T-MoS2@N-g-C3N4 (11.12 mmol L-1 g-1h-1) composite also shows a significant improvement for photocatalytic N2 fixation efficiency in the sacrificial agent (methanol). The improved photocatalytic activity of P-1 T-MoS2@N-g-C3N4 composite is ascribed to the following advantages: 1) Compared to pure g-C3N4, P-1 T-MoS2@N-g-C3N4 composite shows higher light absorption capacity, which can improve the utilization rate of the catalyst to light; 2) The P doping intercalation strategy can promote the conversion of 1 T phase MoS2, which in turn in favor of photogenerated electron transfer and reduce the recombination rate of carriers; 3) A large number of active sites on the edge of 1 T-MoS2 and the existence of N doping in g-C3N4 contribute to photocatalytic N2 fixation.

Correction: Ghanei et al. Effect of Nano-CuO on Engineering and Microstructure Properties of Fibre-Reinforced Mortars Incorporating Metakaolin: Experimental and Numerical Studies. Materials 2017, 10, 1215.

The authors regret that Figures 6 and 11b in [...].

Using photo-induced p-n junction interface effect of CoMn2O4/ß-MnO2 oxidase mimetics for colorimetric determination of hydroquinone in seawater.

Detection of pollutants in seawater faces a great challenge of strong interference, and the facile detection method is lacked. The CoMn2O4/ß-MnO2 p-n junction oxidase mimetics were successfully prepared for colorimetric detection of hydroquinone in seawater. The catalysis ability was enhanced significantly by the photo-induced p-n junction interface effect. It not only promoted the formation of H2O2 by suppressing the recombination of photon-generated carriers, but also provided the driving force for electron transport. The colorimetric detection of hydroquinone was achieved by fading and exhibited good adaptability in seawater. The obtained good recovery rate (97.23%-101.37%) in seawater makes it an inspiring method for practical application. The photo-induced p-n junction interface effect provides an opportunity for developing the application of colorimetric sensing in seawater detection.

Facile preparation of metallic 1T phase molybdenum selenide as cocatalyst coupled with graphitic carbon nitride for enhanced photocatalytic H2 production.

Low-cost, highly active and efficient alternative co-catalysts that can replace precious metals such as Au and Pt are urgently needed for photocatalytic hydrogen evolution reaction (HER). Herein, we show that 1T phase MoSe2 can act as the co-catalyst in the 1T-MoSe2/g-C3N4 composites and we synthesize this composite by a one-step hydrothermal method to promote photocatalytic H2 generation. Our prepared 1T-MoSe2/g-C3N4 composite exhibits highly enhanced photocatalytic H2 production compared to that of g-C3N4 nanosheets (NSs) only. The 7 wt%-1T-MoSe2/g-C3N4 composite presents a considerably improved photocatalytic HER rate (6.95 mmol·h-1·g-1), approximately 90 times greater than that of pure g-C3N4 (0.07 mmol·h-1 g-1). Moreover, under illumination at λ = 370 nm, the apparent quantum efficiency (AQE) of the 7 wt%-1T-MoSe2/g-C3N4 composite reaches 14.0%. Furthermore, the 1T-MoSe2/g-C3N4 composites still maintain outstanding photocatalytic HER stability.